Our company is manufacturing a wide range of
Bitumen Testing Equipment, which is used for the determination of the
softening point of bitumen. It incorporates a slipping clutch mechanism
which makes reading of penetration, and subsequent resetting a simple and
Our quality range of Viscometers is used for
determining the viscosity of cut back bitumen and road oil. The cup lid,
with insulated handle, is fitted with two opposite wedge cams, which engage
under pillars secured to the cup flange. This feature facilitates easy
removal of the lid by rotating the handle a few degrees to disengage the
Tar Viscometer: IS : 1206, BS: 2000 (Part-72) For determining the viscosity
of cut back bitumen and road oil. The viscometer consists of a chrome plated
copper plated copper bath, with a drain valve and a central tube to receive
the test cup and to position the stirrer, and is mounted on a stand with
leveling feet. Stirrer has a curved shield and is provided with an insulated
handle, thermometer socket and swivel support for the valve. Supplied
complete with 10 mm cup and ball valve or 4 mm cup and ball valve as per the
model required. The following models are available. Standard Tar Viscometer,
Electrical Heating with Immersion Heating Elements and Dimmerstat for
controlling the temperature. Suitable for operation on 220 V, 50 Hz, single
phase, AC supply. Complete with 10mm & 4 mm Cup and Valve.
Flash & Fire Point Apparatus / Pensky-Martens Apparatus IS: 1209, IS
1448 (Part 21), ASTM D 93, BS:2839 For determining the flash point of fuel
oils and lubricating oil, bitumen other than cutback bitumen and suspension
of solids in liquid, having a flash point above 49°C. The oil cup is
made of brass, fitted with a thermally insulated lifting handle. The cup
lid, with insulated handle, is fitted with two opposite wedge cams, which
engage under pillars secured to the cup flange. This feature facilitates
easy removal of the lid by rotating the handle a few degrees to disengage
the cams. The shutter opening mechanism is designed for smooth operation and
is operated by a spring handle with a knuled knob. A flame exposure device
(Gas test jet assembly) is mounted over the lid. The manually operated
stirrer has flexible has a flexible shaft. The cup assembly is positioned in
a cast iron air bath, fitted with a chrome plated brass top. The air bath is
mounted on an upright which serves as a gas manifold. Valve controlled
supply lines for adjustable flames are provided with pilot and test flames.
An additional line with control valve supplies gas for use with open flash
clip, in accordance with IS: 1448 (P:66), IS: 1209, A ring support is
provided for the lid when not in use. Electrical heating, with gas test jet
and electric heater with energy regulator. 220V, 50 Hz, Single Phase, AC
Saybolt Viscometer : ASTMD 88, D 244 AASHTOT72 Electrically Heated for the
empirical measurement of Saybolt Viscosity of petroleum products at
specified temperatures between 70deg. F and 210 deg F. This is also used for
determining the Saybolt Furol viscosity of bituminous materials at
temperatures of 250, 275, 300, 350, 400 and 450 deg F. It comprises one each
of Cylindrical Oil Cup, Universal TIP, Furol Tip, Bath fitted with immersion
heater mounted on a stand, Dimmerstat for temperature control, stirrer with
shield, Complete with insulated handle and thermometer support, receiving
flask, withdrawal tube, tube, filter funnel, thermometer support for cup and
circular spirit level. Suitable for operation on 220 V, 50 Hz. Single Phase
- Flow Cup Viscometer No. 4 Simple flow cup of the efflux type is used
for approximate measurements of apparent viscosity for control of
consistency during manufacture and use of paints, lacquers and viscous
products. Flow cup with protective skirt are made from gun metal with
stainless steel orifice and are equivalent to Type B cups. Each cup is
supplied complete with a stand having leveling screws.
Core Cutting/Drilling Machine
We are engaged in manufacturing a wide range of Core
Cutting/Drilling Machine, which is diesel engine (Greaves Ltd.) operated
powered road building drill has been designed specifically for the purpose
of drilling test cores from or holes in roads, airport runways and bridges.
The double precision bit advances with screwed spindle, which provides a
constant, accurate drill pressure, minimum core chipping & long bit
- Core Cutting/Drilling Machine
- The Core Drilling Machine is Petrol Engine (Greaves Ltd.) operated
powered road building drill has been designed specifically for the
purpose of drilling test cores from or holes in Roads, Airport Runways,
Bridges etc. The Machine comprises of two vertical support columns,
which carry the drill head/ engine assembly accurately with the help of
screwed spindle. The 5 Hp Petrol Engine with pulley mechanism works with
minimum vibrations. The double precision bit advances with screwed
spindle, which provides a constant, accurate drill pressure, minimum
core chipping & long bit life.
- The complete assembly is supplied on a rigid metal base with leveling
facility and is suitable for vertically down coring applications only.
For asphalt pavement/Concrete Road. Engine driven Air cooled. Cut upto
100 mm dia specimen with impregnated diamond core bit, Extension core
barrel and adaptor. Water tank also supplied with machine & spray
arrangement for cooling the diamond bit.
- Diamond Bit 100 mm dia, impregnated type.
- Diamond Bit 150 mm dia, impregnated type.
- Barrel 250 mm long for 100 mm dia. bit.
- Barrel 250 mm long for 150 mm dia. Bit.
Benkelman Beam Apparatus & Jaw Crusher
Our company is offering a wide range of Benkelman
Beam Apparatus & Jaw Crusher, which is an improved version of Benkelman
Beam and is a convenient, accurate device for measuring the deflection of
flexible pavements under moving wheel loads. This apparatus is equally
supported at both ends producing a set height between the road surface and
- Benkelman Beam Apparatus It utilizes the technique of using balanced
beam in conjunction with a suitable vehicle to measure road flexure. The
improved Benkelman Beam is a convenient, accurate device for measuring
the deflection of flexible pavements under moving wheel loads. Operating
on a simple lever arm principle, the unit consists of a Reference Beam,
Body, two part Probe Beam and Rear Zero adjust. It is light weight made
- Motor rating:
- Straight Edge as per IRC
- Straight Edge is approximately 3 Meter in length may be used to
determine lateral surface regularly of a road surface. This apparatus is
equally supported at both ends producing a set height between the road
surface and the beam. Any vertical irregularity is measured using
incremented wedges. Measuring wedge is also supplied with the apparatus.
- Camber Template as per IRC
- Small Laboratory Jaw Crusher
- The 'ASEW laboratory crusher is designed to speed up the crushing of
aggregates, ores, minerals, coal, coke, chemicals and other similar
materials. It is compact and of rugged construction for general
laboratory or small pilot plant operation.
- Two jaws of manganese steel are provided in the jaw crusher. The
moveable jaw produces two blows for every revolution. Thus reducing over
sizing to a minimum. A combination of forward and downward stroked with
a rocking action exerts pressure on the coarser material, yet permits
the finished material to pass through the jaws. A hopper is provided at
the top for feeding materials. The smooth jaws ensure a uniform product
and easy cleaning is possible.
|Jaw size :
||100 x150 mm
|Max. size of feed :
||50 mm (approx)
|Product discharge size :
||5 mm to 15 mm.
||100 to 200 kg. (based on material)
|Operation on :
||40 V, 3 ph. 50 Hz. A.C
Complete with a 3 H.P. motor, a starter, 'V belt
pulley drive and mounting. Lab-Pulverizer
Jaw Crushers & Lab Pulverizers
We are engaged in manufacturing and supplying a wide
range of Jaw Crushers, which is available in various sizes, capacities,
operations as per the clients specific requirements. The pulverizer is
useful for assaying, mining and for metallurgical, quarrying, aggregate
processing, chemical, geological and industrial laboratories.
Jaw Crusher: Medium Similar to ASEW 202, but
|Jaw size :
||150 x200 mm
|Max. size of feed
||100 mm (approx)
|Product discharge size :
||5 mm to 20 mm.
||250 to 400 kg. (based on material)
|Operation on :
||440 V, 3 ph. 50 Hz
pair of Jaw 100 mm x 150 mm
Pair of Jaw 150 mm x 200 mm
The 'ASEW laboratory pulverizer is a disc grinder, designed to grind
virtually any material to produce a fine mesh sample in one operation. The
pulverizer is useful for assaying, mining and for metallurgical, quarrying,
aggregate processing, chemical, geological and industrial laboratories. It
is a self-contained grinder, with a rotary disc, having a planetary movement
in a vertical plane.
This feature gives added life to the moving parts and produces a sample of
uniform fineness. Grinding is done between two discs-one stationary and the
other revolving eccentrically at high speed. The discs are made from heat
treated mechanite metal.
With the help of a convenient hand wheel, the size of the final product can
be adjusted. This can be done, even while the machine is in operation. A
self locking device holds the hinged grinding chamber in place and affords
easy and quick access to it, for removal of ground samples and for cleaning.
The Pulverizer is supplied a 3 H.P. motor, a starter, a 'V belt pulley drive
|Disc diameter :
|Maximum feed size :
||8 mm (approx)
|Size of finished product :
||100 mesh to 150 mesh
Discs Stationary & revolving.
Ball Mill: 300 mm x 300 mm Consists of a drum made of welded steel having
an inside diameter of 300 mm x 300mm long, supported on heavy duty ball
All air and water tight cover is provided to close the 100 mm wide opening
along the entire length of the drum. A reduction gear driven by a motor
rotates the Ball mill at 28-30 RPM.
Supplied complete with twelve 19 mm diameter hardened steel balls and an
automatic revolution counter. One tray also provided for collecting the
sample. Operation on : 220 V, single ph., 50 Hz., A.C. supply.
Ball Mill: 300 x350 mm
- Set of twelve steel balls as specified.
- Receiver tray.